ts5213 80ma low noise ldo voltage regulator with enable function 1 / 8 version: e 07 sot - 25 sot - 353 general description ts5213 is an efficient linear voltage regulator with ultra low noise output, very low dropout voltage (typically 5 0mv at light loads and 3 2 0mv at 80ma), and very low gr ound current (225ua at 20ma), providing high output current even when the application requires very low dropout voltage. the chip enable (en) includes a cmos or ttl compatible input allows the output to be turned off to prolong battery life. when shutdown, power consumption drops nearly to zero. ts5213 is included a precision voltage reference, error correction circuit, a current limited output driver, over temperature shutdown and revered battery protection . features ultra low noise output output curren t up to 80ma low power consumption ?ero?off - mode consumption logic controlled electronic enable current limit & thermal shutdown protection ordering information part no. package packing ts5213cx5 xx rf sot - 25 3kpcs / 7 reel ts5213cu5 xx rf sot - 353 3kpc s / 7 reel note: where xx denotes voltage option, available are 50 =5.0v 33 =3.3v 25 =2.5v contact factory for additional voltage options. application cellular telephones palmtops, notebook computers battery powered equipment smps post regulator and dc to dc modules high - efficiency linear power supplies portable application block diagram typical application circuit en may be connected to v in pin to regulation on c in > 0.1uf in basic operating c out >0.47uf in low noise oper ating pin definition : 1. input 2. ground 3. enable 4. n/c 5. output pin definition : 1. enable 2. n/c or ground 3. ground 4. output 5. input v out v in en on off c o ut 0.47uf ts5213cx5xx v out v in en on off c out 0.47uf ts5213cu5xx
ts5213 80ma low noise ldo voltage regulator with enable function 2 / 8 version: e 07 absolute maximum rating (note 1) parameter symbol limit unit input supply voltage v in - 20~ +20 v enable input voltage v ce - 20~ +20 v power dissipation (note 2) p d internal limited sot - 25 220 thermal resistance so t - 353 ? ja 450 o c/w operating junction temperature range t j - 40 ~ +125 o c storage temperature range t stg - 65 ~ +150 o c lead soldering temperature (260 o c) 5 s recommend operating rating (note 2) parameter symbol limit unit input supply voltage v in +2.5 ~ +16 v enable input voltage v ce 0 ~ v in v electrical specification ( v in =vo+1v, io=1ma, c ou t=0.47uf, v en 2v, t j = 25 o c, unless otherwise specified. ) parameter conditions min typ max u nit v in =vo + 1v - 3 -- 3 output voltage - 40 c t j +125 c - 4 -- 4 % output voltage temp . coefficient (note 5) -- 50 200 ppm/ o c line regulation vo+1v v in 16v -- 0. 008 0.3 % load regulation (note 6) 0.1 ma i o 80m a -- 0.08 0.3 % i o = 100u a -- 50 -- i o = 2 0ma -- 23 0 30 0 i o = 50 ma -- 28 0 370 dropout voltage (note 7) i o = 80 ma -- 32 0 42 0 mv quiescent current v e n 0.4v (shutdown) -- 0.01 1 0 u a i o = 100u a -- 80 -- i o = 20 ma -- 225 750 i o = 50 ma -- 850 -- ground pin current ( note 8) v e n 2v (ac tive) i o = 80 ma -- 1800 3000 ua output current limit v out =0v -- 250 500 m a power supply rejection ratio at f=100hz, io=100ua, -- 6 5 -- db thermal regulation (note 9) -- 0.05 -- %/w enable function enable input logic - low voltage regulation shutdown -- -- 0.6 v enable input logic - high voltage regulation enable 2.0 -- -- v v il 0.6v -- 0.01 1 enable input current v ih 2.0v -- 15 50 ua
ts5213 80ma low noise ldo voltage regulator with enable function 3 / 8 version: e 07 electrical specification (continue) n ote 1: exceeding the absolute maximum rating may damage the device. note 2: the maximum allowable power dissipation at any ta is pd(max) = [t j(max) - ta ] + ? ja . exceeding the maximum allowable power dissipation will re sult in excessive die temperature, and the regulator will go into thermal shutdown. note 3: devices are esd sensitive. handling precautions recommended. note 4: the device is not guaranteed to function outsi de its operating rating. note 5: output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. note 6: regulation is measured at constant junction te mperature using low duty cycle pulse testing. parts are tested for load regulation in the load range from 1ma to 80ma. changes in output voltage due to heating effects are covered by the thermal regulation spe cification. note 7: dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1v differential. note 8: ground pin current is the regul ator quiescent current plus pass transistor base current. the total current drawn from the supply is the sum of the load current plus the ground pin current. note 9: thermal regulation is defined as the change in output vo ltage at a time t after a change in power dissipation is applied, excluding load or line regulation effects. specifications are for a 80ma load pulse at v ih =16v for t=10ms. application information enable input ts5213 series feature an active - high (>2v) enable (en) input that allows on/off control of the regulator. current drain reduces to zero when the device is shutdown, with only micro - amperes of leakage current. the en is compatible with cmos logic in terfacing. en may be directly tied to v ih and pulled up to the maximum supply voltage. input capacitor requirement an input capacitor of 0.17uf or greater is recommended when the device is more than 10 away from the bulk ac supply capacitance or when the supply is a battery. output capacitor requirement the ts5213 series requires an output capacitor to maintain stability and improve transient response is necessary. the ts5213 is ultra stable, requiring only 0.47uf of output capacitance for stability. it is stable with all type of capacitors, including the tiny, low - esr ceramic chip capacitors. the output capacitor value may be increased without limit. no load stability the ts5213 series will remain stable and in regulation with no load, unlike many other voltage regulators. this is especially important in cmos ram keep alive applications. fixed output regulator application low noise fixed voltage application ts5213 series is offered a smaller system solution, it is only required a small multilayer ceramic capacitor for stability. v out v in c out 0.47uf en on off
ts5213 80ma low noise ldo voltage regulator with enable function 4 / 8 version: e 07 application information (continue) thermal characteristics ts5213 series is designed to provide 80ma of continuous current in a very small package. maximum power dissipation can be calculated based on the output current and the voltage drop across the part. to determine the maximum power dissipation of the package, use the juncti on - ambient thermal resistance of the device and the following basic equation: p d(max) = [ t j(max) t a ] / ja t j(max) is the maximum junction temperature of the die(125 o c), and ta is the ambient operating temperature. ja is layout dependent, the actual p ower dissipation of the regulator circuit can be determined using the equation: p d = (v in v out ) * i out + v in * i gnd substituting pd(max) for pd and solving for the operating conditions that are critical to the application will give the maximum opera ting conditions for the regulator circuit. for example, when operating the ts5213cx550 at room temperature with a minimum footprint layout, the maximum input voltage for a set output current can be determined as follows: p d(max) = (125 o c 25 o c) / 220 o c/w p d(max) = 455mw the junction to ambient thermal resistance for the minimum footprint is 220 o c/w, the maximum power dissipation must not be exceeded for proper operation. using the output voltage of 5.0v and an output current of 80ma, the maximum input vo ltage can be determined. form the electrical characteristics table, the maximum ground current for 80ma output current is 1ma. 445mw = (v in 5.0v ) * 80ma + v in * 1.8ma 445mw = v in * 80ma 5.0 * 80ma + v in * 1.8ma 445mw = v in * 80ma 400mw + v in * 1.8ma 845mw = v in * 81.8ma v in (max) = 10.33v therefore, a 5.0v application at 80ma of output current can accept a maximum input voltage of 10.33v in a sot - 25 package.
ts5213 80ma low noise ldo voltage regulator with enable function 5 / 8 version: e 07 electrical characteristics curve figure 1. output voltage vs. input vo ltage figure 2. ground current vs. output current figure 3. dropout voltage vs. output current figure 4. short circuit current vs. input voltage figure 5. ripple rejection vs. frequency figure 6. ripple rejection vs. frequency
ts5213 80ma low noise ldo voltage regulator with enable function 6 / 8 version: e 07 sot - 25 mechanica l drawing marking diagram t = device code x = voltage code ( 5 = 5.0v, s = 3.3v, k = 2.5v) y = year code m = month code ( a =jan, b =feb, c =mar, d =apl, e =may, f =jun, g =jul, h =aug, i =sep, j =oct, k =nov, l =dec) l = lot code sot - 25 dimension millimeters inches dim min max min max. a+a 1 0.09 1.25 0.0354 0.0492 b 0.30 0.50 0.0118 0.0197 c 0.09 0.25 0.0035 0.0098 d 2.70 3.10 0.1063 0.1220 e 1.40 1.80 0.0551 0.0709 e 1.90 bsc 0.0748 bsc h 2.40 3.00 0.09449 0.1181 l 0.35 bsc 0.0138 bsc ? 1 0 10 0 10 s1 0.95 bsc 0.0374 bsc
ts5213 80ma low noise ldo voltage regulator with enable function 7 / 8 version: e 07 sot - 353 mechanical drawing marking diagram x = voltage code ( 5 = 5.0v, s = 3.3v, k = 2.5v) y = year code m = month code ( a =jan, b =feb, c =mar, d =apl, e =may, f =jun, g =jul, h =aug, i =sep, j =oct, k =nov, l =dec) sot - 353 dim ension millimeters inches dim min max min max a 1.80 2.20 0.0709 0. 0866 b 0.25 0.40 0. 0 098 0.0157 c 1.30(typ) 0.0512(typ) d 1.15 1.35 0.0453 0.0531 e 1.80 2.40 0.0709 0.0945 f 0.35 0.50 0.0137 0.0197 g 0.80 1.10 0.0315 0.0433 h 0.10 0.45 0.0039 0.0177
ts5213 80ma low noise ldo voltage regulator with enable function 8 / 8 version: e 07 notice specifications of the products displayed herein are subject to change without notice. tsc or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. inform ation contained herein is intended to provide a product description only. no license, express or implied, to any intellectual property rights is granted by this document. except as provided in tsc? terms and conditions of sale for such products, tsc assum es no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of tsc products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright , or other intellectual property right. the products shown herein are not designed for use in medical, life - saving, or life - sustaining applications. customers using or selling these products for use in such applications do so at their own risk and agree t o fully indemnify tsc for any damages resulting from such improper use or sale.
|
